Automatic Simple Hydraulic Jacks for Tank Construction

1,Working principle

Hydraulic lifting device (package unit) is evenly distributed around tank inner wall. Tank top and upper (the first layer) wall plates are lifted first and then install and weld wall plates of tank body. Self locking hydraulic jack and hydraulic hoist composing of lifting frame and lifting rod are adopted. When oil enters hydraulic jack, upper clamp fastens and lifts lifting rod and expansion ring and mobilize tank (including tank top) to ascend upward. When oil returns to jack, upper clamp returns with piston and lower clamp automatically fastens lifting rod without gliding. The jack repeats the movement and make lifting rod ascend with tank to designated height (spare height for next layer of plate). After butt weld of next layer of wall plates, open upper and lower loosening device and loosen upper and lower clamp to make lifting rod and expansion ring descend to lower expanded and welded rib plate of the next layer of wall plates and then lift. Repeat the process and ascend welded tan till the last layer of wall plates are installed and welded. The installation of the whole storage tank is completed.

2,Technical parameter

SQD-XXX-100S.F Hydraulic jack

Model	Rated lifting weight	Theory lifting weight	Rated oil pressure	Single hydraulic stroke	Lifting height	Glissade capacity
SQD-120-100S.F	120KN	123KN	18Mpa	100±0.5mm	2.6m	≤5mm
SQD-160-100S.F	160KN	163KN	20Mpa	100mm	2.6m	≤3mm
SQD-250-100S·F	250KN	253KN	25Mpa	100mm±1mm	2.6m	≤3mm
SQD-350-100S·F	300KN	303KN	20Mpa	100mm	2.6m	≤3mm
SQD-500-100S.F	500KN	503KN	25Mpa	100±0.5mm	2.6m	≤5mm
SQD-1000-200S·F	1000KN	1003KN	20Mpa	150mm	2.6m	≤3mm

Pump station

Model	Maximum pressure	Power	Rated oil flow	Motor rotate speed	Oil tank capacity	System oil type
YB-40	25Mpa	11kw	40L/min	1470r/min	240L	L-HM46#   antiwear hydraulic oil
YB-60	25Mpa	18.5kw	60L/min	1470r/min	400L
YT-90	25Mpa	30kw	90L/min	1470r/min	400L

Jack support

Model	Total height	Lifting rod height	Slider stroke	Lifting rod diameter	Distance  between  expansion    loop  support  to    ground
TSJ-120-2600L	3460mm	3900mm	2630mm	φ32mm	310mm
TSJ-500-2950L	4040mm	4700mm	2950mm	φ60mm*4.7m	430mm

3,Product features

1).Simple jack adopts low relaxation steel strand, as long as there is a reasonable bearing lifting point, lifting height is not restricted;

2).Through the expansion and combination of simple jacks, the lifting weight, span and area are unlimited;

3).Small volume, light weight, large bearing capacity, convenient and flexible installation, especially suitable for small space or indoor large tonnage tank lifting;

4).The simple jack has reverse motion self-locking, which makes the lifting process very convenient, and the storage tank can be locked reliably at any position in the lifting process for a long time;

5).The jack has a high degree of automation, convenient and flexible operation, with automatic operation, semi-automatic operation, single point adjustment, manual operation and other operations.LCD display, touch screen display, button operation panel display, very intuitive.And the control system is equipped with self-correction protection procedures, even if the misoperation will not cause accidents;

6).Using this series of simple unfixing Holding -latch hydraulic Jack, the construction period is short, the cost is low, the economic benefit is good.

4,Construction site photos

  Wincoo Engineering Co.,ltd is a hydraulic machinery manufacturing company integrated with design, development, production and sales, which mainly manufactures LYT-type chain-type hydraulic hoist, SQD unfixing holding-latch hydraulic hoist and supporting products. Such products are mainly used for inverted lifting and installation of steel storage tanks. Founded in 2003, after years of concentrated scientific research and development, the company obtained the patent certificate of "Utility Model Hydraulic Hoist’ issued by "China National Intellectual Property Administration", and the right to use the trademark of "WINCOO" in 2008, so as to enable products of Wincoo Engineering Co.,ltd to quickly become Chinese brands.

  Since entering Chinese market for more than 10 years, products of Wincoo Engineering Co.,ltd has been sold in nearly thirty provinces, cities and autonomous regions in China, and some overseas markets. The company has production line of advanced technology; meanwhile, Wincoo Engineering Co.,ltd designs, develops and processes products for famous domestic installation companies. With professional team, strict management and excellent equipment, the company strives to create the brand of "WINCOO", hydraulic hoist and series supporting products. As an expert of hydraulic hoist, WINCOO with charm of high technology is keen, innovative and forging ahead to establish design language of the company. In an all-inclusive and absorbing and open-minded manner, the hydraulic hoist and hydraulic pump station are perfectly combined to form hydraulic lifting equipment (hydraulic jacking equipment). As the founder and disseminator of hydraulic hoist, WINCOO has been building the inverted hydraulic lifting equipment and production technology of Dongfang installation engineering for a long time.

  Wincoo Engineering Co.,ltd is committed to the research and development of LYT-type chain-type hydraulic hoist, SQD-type unfixing holding-latch hydraulic hoist and the supporting equipment. The LYT-type and SQD-series products have been widely used in various projects (inverted lifting, translation, jacking, and climbing, etc.) by major installation companies all over the country, and have achieved satisfactory results.

  WINCOO sticks to improve core competitiveness by virtue of corporate culture, thus setting a good social image of the company during development. "Those hoping to expand the company must study hard from the moment, and the pursuit is endless". "WINCOO" will continuously forge ahead, contributes to the course of installation project in China and permanently moves forward to forge the monument of hydraulic lifting industry in China.